You Don’t Have to Spend a Fortune on a Concrete Fireplace—This Couple Did It for $236

A new reason to gather.
Lydia Geisel Avatar

We may earn revenue from the products available on this page and participate in affiliate programs.

For Dan and Sarah Pollio, the husband-and-wife team of Joinery and Design Co., the heart of the home isn’t the kitchen—it’s the hearth. Before settling into their newly built Minnesota house, the couple decided to take their living room fireplace into their own hands. “I really wanted to have an organic, textured feel for the fireplace,” shares Sarah. “Dan and I started looking into stucco, but eventually we realized it just wasn’t in our budget. Then we came up with this concept of a DIY concrete fireplace look.”

Call it what you want—faux concrete, concrete inspired, concrete-esque—the imitation treatment was appealing for a very good reason: Real concrete is pricey. “Normally, the way you get a concrete fireplace is by forming the mantel and chimney from scratch,” explains Dan. “That’s definitely something you’d see in a $2 million to $3 million home.” Using Ardex Feather Finish, a self-drying, cement-based mixture, the Pollios pulled off their DIY concrete fireplace for just $236. Ahead, the pair walks us through their budget-friendly fireplace hack, step-by-step.

The Supplies

Step 1: Get Close and Personal

Photography Courtesy of Joinery and Design Co.

Because the Pollios didn’t have existing drywall or a mantel to work around, they went straight for the Durock—cement boards that are also typically used as backers for tile or stone. They screwed each panel into the wood frame with cement board screws and added the corner bead to keep the edges and seams sharp and clean. “There are certain clearances you have to follow, depending on your fireplace type,” says Dan. “The nice part is, the Durock is considered flame resistant, so most city and state codes will allow you to go right up to the fireplace with it.”

Step 2: Draw the Line

Photography Courtesy of Joinery and Design Co.

In order to get a smooth finish before you skim coat, you’ll have to tape and mud the joints just as you would with drywall. Using the Ardex Feather Finish mix, take your trowel and fill in the seams between the adjacent Durock sheets. Smooth the compound as you progress. While the mixture is still moist, use Sheetrock joint tape to cover the mixture to keep it in place. Apply one more layer of the cement finish over the tape.

The most time-consuming part of this process will be waiting for the initial joint coats to dry. “It basically took us a day to screw all the sheets on, and, in our case, we also used metal trim around the fireplace to give it a nice finish where the sheets ended,” says Dan. “Let that dry overnight, and then you can start doing the full skim coat.”

Step 3: Skim Coat, But Speed It Up

Photography Courtesy of Joinery and Design Co.

This is the part where you get to call upon your inner artist. Still, you won’t want to take too much time for contemplation as you work across the surface. “The Ardex Feather Finish has what’s called a 15-minute working time. Mix as much as you can use in 15 to 20 minutes and start spreading it on,” says Dan. Were you to create your mixture in a bucket and walk away for lunch, the compound would be rock solid by the time you came back. “You have to keep up with the process fairly quickly,” says Sarah. “There aren’t any coffee breaks in between.”

Apply the cement mixture to the fireplace surface with your trowel. How many coats you apply is really up to you and the look you’re going for. If you decide you don’t like the texture of an area that’s beginning to dry, come back to it later and touch it up. “It almost feels like you’re making art,” she adds.

Step 4: Smooth It Out

This part is optional. If you prefer a sleeker finish to that of stucco, Dan suggests keeping a sponge and bucket on hand. “There are two ways to do this. If you want it really smooth, apply it and then take a damp sponge and lightly wipe [the surface]. It gives it a softer texture,” he says. The Pollios ended up doing a little bit of both. Because the material sticks to the wall really well, you can play around with the composition. “I think one thing we wanted to do in this house was give it an organic look,” explains Sarah. “Our plan is to always try to DIY and make our projects look as high-end and professional as possible. We feel like we really achieved that.”

#9 x 1-5/8 in. Serrated Flat Head Star Drive Cement Board Screws, The Home Depot ($35)

Ardex Feather Finish, Amazon ($37)

Drywall Joint Tape, Amazon ($7)

1/2 in. x 12 in. Ceramic Demi-Bullnose Wall Trim Tile, The Home Depot


This story was originally published in June 2019. It has since been updated.

Lydia Geisel Avatar

Lydia Geisel

Home Editor

Lydia Geisel has been on the editorial team at Domino since 2017. Today, she writes and edits home and renovation stories, including house tours, before and afters, and DIYs, and leads our design news coverage. She lives in New York City.